山東洪雨防水工程有限公司
聯系人：孔經理
手機：132-7531-6008
電話：0531- 87186527 / 8285668
郵箱：2908667081@qq.com
網址：www.www.jianop.cn
地址：山東省濟南市市中區愛都小學南
濟南專業防水http://www.tianyujian.com/介紹在酸雨較重、濕度大、腐蝕性較強的地區，一般施工單位普通做法是在找平層上刷冷底子油當作隔離層用，之后就澆剛性防水層，為保證屋面三年的保修期內不漏水，又在剛性層上做一道二布三油防水層，工程驗收時，甲方看到屋面黑油油的又好看，其實這樣將油膏放在面層，容易老化，使用年限不長，三年后又來補漏。為了避免這類情況發生，在施工中因地制宜，取長補短，把面上的這一層二布三油卷材防水層做在找平層與剛性層之間，既起了隔離層的作用，又不被日曬雨淋，既防止油膏老化，又起了防水作用。
1、濟南專業防水介紹基層上涂刮基層處理劑，要求薄而均勻，一般干燥后，當不粘手才能鋪貼卷材；卷材防水層的鋪貼一般應由層面最低標高處向上平行屋脊施工，使卷材按水流方向搭接，當屋面坡度大于10％時，卷材應垂直于屋脊方向鋪貼。
Jinan professional waterproof introduce Scraping the grassroots primary treatment agent, thin, uniform requirements, usually after dry, sticky when to Stones roll; Stones should normally be the minimum level of waterproofing membrane at
a parallel upward elevation roof construction, coil according to the flow direction so that the lap, when the roof slope greater than 10%, the roof membrane should be perpendicular to the direction of paving.
2、濟南專業防水談到剝開卷材脊面的隔離紙，將卷材粘貼于基層表面，卷材長邊搭接保持50mm，短邊搭接保持70mm，卷材要求保持自然松弛狀態，不要拉得過緊，卷材鋪妥后，應立即用平面振動器全面壓實，垂直部位用橡膠榔頭敲實。
Jinan professional waterproofing membrane lands comes to ripping isolation paper, the membrane attached to the primary surface, roll the long side of the lap to keep 50mm, short side lap keep 70mm, coil required to maintain the natural relaxed state, do not pull too tight, roll shop after properly, you should immediately fully compacted plane vibrators, vertical area with a rubber hammer to knock reality.
3、濟南專業防水http://www.tianyujian.com/提醒卷材壓實后，將搭接部位掀開，用油漆刷將搭接粘接劑均勻涂刷，在掀開卷材接頭之兩個粘接面，涂后干燥片刻手感不粘時，即可進行粘合，再用橡膠榔頭敲壓密實，以免開縫造成漏水；防水層施工溫度選擇5℃以上為宜。
Jinan professional waterproofing membrane compaction reminder, the site will be opened lap, lap paintbrush brushing uniform adhesive bonding surface coils in both joints opened it, after a while feel dry non-stick coating when the bond
can be carried out, then the rubber hammer to knock compacting pressure, in order to avoid leaks caused slotted; waterproof layer construction more than 5 ℃ temperature selection is appropriate.